Choosing between resin, block paving and tarmac comes down to budget, the look you want, how much upkeep you will accept and how the drive will drain. This guide compares the three side by side using published UK prices, credited to their sources, and also looks briefly at gravel and imprinted concrete.
The table below sets out installed prices from the UK guides we use, with each figure kept to its own source rather than blended into a single average. The sources measure slightly different things, so the notes in brackets matter. In particular, some resin prices exclude the base, while most block paving and full dig-out tarmac prices include excavation and a sub-base.
Read across the rows and a broad pattern appears. Tarmac and gravel tend to sit at the lower end, resin and block paving overlap in the middle, and imprinted concrete reaches the top of the ranges. Your own drive could buck that pattern, because the state of the ground underneath often matters more than the surface you choose.
| Material | Price per m² | Example whole driveway | Source |
|---|---|---|---|
| Resin driveway | £60 to £95 (materials and labour) | 60m²: £3,500 to £5,500 | MyJobQuote (October 2026) |
| Resin bound | £40 to £55 (base preparation excluded) | 40m² on existing base: £1,600 to £2,800; on new base: £2,600 to £4,600 | Less.co.uk (April 2026) |
| Block paving | £70 to £120 (installed) | 40m²: average £3,800 | Less.co.uk (April 2026) |
| Block paving, concrete blocks | Not quoted here | 60m²: £4,500 to £6,000 | MyJobQuote (October 2026) |
| Tarmac, full dig-out | £40 to £60 | 40m²: £1,600 to £2,400 | Less.co.uk (April 2026) |
| Tarmac, new | £45 to £100 (installed) | 60m²: £2,500 to £5,000 | MyJobQuote (October 2026) |
| Gravel | £40 to £100 (installed) | 30m²: £1,200 to £2,200 | MyJobQuote (September 2026) |
| Gravel | £50 to £100 (fully installed) | 50m²: £2,500 to £5,000 | Less.co.uk (April 2026) |
| Imprinted concrete | £100 to £130 (materials and labour) | 60m²: average £7,100 | MyJobQuote (October 2026) |
| Imprinted concrete | £60 to £100 | 40m²: £2,400 to £4,000 | Less.co.uk (April 2026) |
For a closer look at each material, see our guides to resin driveway cost, block paving cost and tarmac driveway cost. Each one breaks the price down by size, groundwork and extras such as edging and drainage. They also explain what a good quote should include, so you can compare installers on the same terms.
On price the two are closer than many people expect. MyJobQuote gives £3,500 to £5,500 for a 60m² resin drive and £4,500 to £6,000 for a 60m² concrete block drive, while Less.co.uk gives an average of £3,800 for 40m² of block paving. Resin can come in well below that when it goes over a sound existing base, which Less.co.uk prices at £1,600 to £2,800 for 40m².
The look is where they really differ. Resin bound gives a smooth, seamless finish in a wide choice of natural stone, quartz and marble blends, and it suits modern houses and drives with curves. Block paving has a more traditional, textured appearance, with patterns such as herringbone and contrasting borders, and it sits comfortably in front of older brick houses.
Practically, block paving copes well with heavy vehicles and can be lifted and relaid if a section sinks or a pipe needs repairing. Resin bound is firm, has no joints for weeds to root in and, on a suitable base, drains straight through. It does need a stable base and careful installation, because faults in the ground below will show through the thin surface layer.
Tarmac is usually the cheaper of the two. Less.co.uk gives a full dig-out tarmac drive at £40 to £60 per m², or £1,600 to £2,400 for 40m², against £2,600 to £4,600 for 40m² of resin bound on a new base. MyJobQuote's figures for a 60m² drive are £2,500 to £5,000 for new tarmac and £3,500 to £5,500 for resin.
Tarmac is hard-wearing, quick to lay and practical for long or busy drives, but it offers a limited choice of finish. Black is standard, and MyJobQuote says colour adds £10 to £20 per m². Resin gives far more choice of colour and texture, and it tends to suit a house where the drive is a visible part of the frontage.
Drainage is another clear difference. Standard tarmac is impermeable, so water must be directed to a drain, a soakaway or a permeable area, whereas resin bound laid on a permeable base lets water soak through. Porous asphalt is available as a permeable form of tarmac, but our sources do not give a separate price for it, so quotes vary.
None of the price guides we rely on gives a lifespan figure we are confident enough to quote, so we describe it in general terms. All three surfaces can last many years when they are laid on a properly prepared base, and a poor sub-base will shorten the life of any of them. How well the drive was installed usually matters more than which material was chosen.
Block paving needs the most routine care. Weeds and moss can grow in the joints, and many owners have the drive cleaned, re-sanded and sealed from time to time. The pay-off is that repairs are simple, because individual blocks can be lifted and relaid, and MyJobQuote gives lift and relay at £20 to £45 per m².
Resin bound needs little more than an occasional sweep and wash, though oil and fuel spills should be cleaned up quickly. Repairs are harder to hide, because new resin rarely matches weathered resin exactly. Tarmac is easy to patch, but patches tend to show, and the surface can soften in hot weather and fade from black to grey over the years.
Drainage affects whether a front driveway needs planning permission. GOV.UK guidance says that if the surface to be covered is more than 5 square metres, planning permission will be needed for traditional impermeable driveways that do not direct water to a permeable area. It gives gravel, permeable concrete block paving and porous asphalt as examples of permeable surfacing.
The Planning Portal says a new or replacement driveway of any size does not need permission if it uses permeable surfacing or if rainwater is directed to a lawn or border to drain naturally. Resin bound on a permeable base, permeable block paving, gravel and porous asphalt can all meet that test, while standard tarmac, standard block paving and imprinted concrete usually need drainage to a permeable area. These rights apply to houses rather than flats or maisonettes, and conservation areas, listed buildings and Article 4 Directions can change what is allowed, so check with your local planning authority and read our driveway planning permission advice.
Gravel is among the lower-cost ways to create a new drive, and it is naturally permeable. MyJobQuote gives £40 to £100 per m² installed, and £1,200 to £2,200 for 30m², while Less.co.uk gives £50 to £100 per m² and says a gravel grid adds £10 to £20 per m². Gravel does need raking and topping up, it can spread onto paths and the pavement, and it is less comfortable for wheelchairs and pushchairs than a solid surface.
Imprinted concrete is poured concrete stamped with a pattern to look like brick, stone or cobbles. MyJobQuote gives £100 to £130 per m² including excavation, sub-base, imprinting and sealing, while Less.co.uk gives £60 to £100 per m², and the two ranges differ enough that it pays to get several quotes. It needs resealing from time to time, which MyJobQuote prices at £4 to £8 per m², and cracks are difficult to repair without the patch showing.
There is no single best driveway material in the UK, because the right choice depends on your budget, your house and how the drive is used. Tarmac suits a practical, lower-cost drive, block paving suits a traditional look and easy repairs, and resin suits a smooth, decorative finish that can drain freely. Gravel and imprinted concrete are worth considering at either end of the budget scale.
The surest way to compare is to get quotes for more than one material on the same drive. Sussex Driveway connects homeowners with local driveway installers rather than doing the work itself. Fill in our short form or call 01273 115520 to get up to 3 free quotes, with no obligation to go ahead.
It can be, especially when resin goes over a sound existing base. MyJobQuote gives £3,500 to £5,500 for a 60m² resin drive and £4,500 to £6,000 for 60m² of concrete block paving. A new base for resin narrows the gap.
Tarmac is usually cheaper. Less.co.uk gives £1,600 to £2,400 for a 40m² full dig-out tarmac drive, against £2,600 to £4,600 for 40m² of resin bound on a new base.
Resin bound and tarmac generally need less routine care than block paving, which can collect weeds and moss in its joints. Gravel needs regular raking and topping up. Any surface benefits from an occasional clean.
GOV.UK names gravel, permeable concrete block paving and porous asphalt as permeable surfaces, and resin bound can be permeable when laid on a free-draining base. Standard tarmac, standard block paving and imprinted concrete need drainage to a permeable area if a front drive is over 5 square metres.
Block paving is the easiest, because blocks can be lifted and relaid with little sign of the work. Tarmac patches and resin repairs tend to show, and cracks in imprinted concrete are hard to hide.
Prices are published UK averages and include labour. Every job is different, so the quotes you receive will reflect your own property, access and materials.
Tell us about the job and up to 3 local driveway installers will be in touch with quotes. There is no charge and no obligation. Or call 01273 115520.
We use essential cookies to make this site work. With your permission, we would also like to use Google Analytics cookies to understand how people use the site so we can improve it. We do not use advertising cookies. You can change your mind at any time using the cookie settings button. Read our cookie policy for more information.