Driveway sealing and block paving sealing in Sussex

Wet-look, natural and anti-slip finishes for block paving, resin and concrete. Compare up to 3 free quotes from local installers.

Sealing is a sensible way to look after a driveway once it has been properly cleaned. A good sealer helps the surface resist water, oil and fuel stains, makes it harder for weeds to take root in the joints and can help your block paving, resin or concrete keep its colour for longer. The result depends heavily on the preparation and the product, so it is worth choosing an installer who explains both clearly.

We do not seal driveways ourselves. We pass your enquiry to up to 3 local installers and cleaners across Brighton, Worthing, Eastbourne and the rest of Sussex, and they will be in touch to arrange a quote. Professional sealers are often different from the retail products sold for DIY use, so ask each installer which product they recommend for your surface and why.

Why seal your driveway?

An unsealed driveway takes the full force of the British weather. Rain soaks into the surface and joints, frost can open up small cracks, and sunlight gradually fades the colour of some blocks. Weeds take hold in the jointing sand, ants can nest beneath the blocks and oil from cars soaks into porous surfaces.

Sealing does not make a driveway maintenance free, but it can slow down many of these problems. On block paving, a jointing sealer also helps bind the sand between the blocks so that it is less likely to wash out, which is a common complaint with older block paved drives. For the best result, have your driveway properly cleaned before it is sealed.

Block paving sealing options

Wet-look finish

A wet-look sealer deepens the natural colour of the blocks and gives a just-rained appearance. It brings out reds, charcoals and buffs, and suits decorative block paving where you want the colour to stand out. Some wet-look products can be more slippery, so it is worth asking about this on sloping drives.

Natural or matt finish

If you like the look of your blocks as they are, a matt sealer gives similar protection without changing the appearance much. It helps with water and stain resistance and binds the jointing sand, while leaving the surface looking close to its natural state.

Anti-slip sealer

For driveways on a slope or paths that see a lot of foot traffic, many installers can add an anti-slip additive to the sealer. This keeps most of the protective benefit while improving grip in wet weather.

What a good sealing job involves

1

Deep clean

Sealing over a dirty surface locks the dirt in, so a sealing job should always start with a thorough clean. That usually means pressure washing, moss and algae treatment and work on any oil or rust stains.

2

Joint repair and re-sanding

On block paving, the joints are checked and any missing or degraded sand is replaced with kiln-dried jointing sand. This helps the sealer bond properly and keeps the blocks firmly locked together.

3

Drying time

The surface must be completely dry before any sealer goes on, which can take a day or more depending on the weather. Sealing too soon is a common cause of clouding, peeling and trapped moisture.

4

Sealer application

Sealer is usually applied by low-pressure sprayer or roller. Many installers prefer two thinner coats to one heavy coat, because it tends to give a more even finish and better adhesion.

5

Curing

The sealed surface then needs time to cure before it can take foot traffic and cars. Your installer should tell you how long to keep off it, as this depends on the product and the weather.

Common block paving sealing problems and how to avoid them

Done badly, sealing can cause more problems than it solves. These are the issues that come up most often, and the questions worth asking an installer before work starts.

White clouding or hazing

This usually happens when sealer goes onto a surface that is still damp. Ask how the installer will make sure the drive is fully dry first.

Peeling or flaking

This is often caused by poor cleaning beforehand or an unsuitable product. A thorough clean and the right sealer for the surface help prevent it.

Slippery surface

Applying too much sealer can leave a slippery film, especially on slopes. Ask about coverage rates and whether an anti-slip additive is worth using.

Uneven finish

Patchy application leaves some areas glossier or darker than others. Even spraying or rolling in a consistent pattern avoids this.

Yellowing over time

Some sealers can discolour as they age in sunlight. Ask which product will be used and how it is expected to wear.

How long does driveway sealing last?

How long a sealer lasts depends on the product, how well the surface was prepared, how much traffic the drive takes and how exposed it is to the weather. Sealers wear gradually rather than failing all at once, so you will usually notice water no longer beading on the surface or stains soaking in more easily. Ask your installer how long they expect their chosen product to last on your drive, and plan a regular clean in between to keep the surface in good condition.

Driveway sealing prices

MyJobQuote puts sealing a 30 square metre drive at £200 to £250 and a 60 square metre drive at £300 to £400, with block paving at £7 to £15 per square metre. MyBuilder gives £4 to £8 per square metre to seal block paving, £6 to £10 per square metre to re-sand and seal it, £3 to £6 for tarmac and £5 to £9 for resin bound. If you need a clean first, MyJobQuote gives £300 to £450 for cleaning and sealing a 60 square metre drive.

The sources do not agree exactly, so ask each installer for a written quote that says whether cleaning and re-sanding are included. Our driveway cleaning cost guide has more detail.

Sources for the prices on this page

Areas we cover

We pass driveway sealing enquiries to local installers across Sussex, including Brighton and Hove, Worthing, Eastbourne, Hastings, Crawley, Horsham, Haywards Heath, Lewes, Shoreham, Littlehampton, Bognor Regis, Chichester and the surrounding areas.

Frequently asked questions

How much does driveway sealing cost?+

MyJobQuote (checked October 2026) puts sealing a 30 square metre drive at £200 to £250 and a 60 square metre drive at £300 to £400, with block paving at £7 to £15 per square metre. If you need a clean first, it gives £300 to £450 for cleaning and sealing a 60 square metre drive.

Does the cost of sealing depend on the surface?+

Yes. MyBuilder gives £4 to £8 per square metre to seal block paving, £6 to £10 per square metre to re-sand and seal it, £3 to £6 for tarmac and £5 to £9 for resin bound.

How long does driveway sealing last?+

It depends on the product, how well the surface was prepared, how much traffic the drive takes and how exposed it is to the weather. Sealers wear gradually, so ask your installer how long they expect their chosen product to last on your drive.

Why does sealer sometimes go cloudy?+

White clouding usually happens when sealer goes onto a surface that is still damp. The surface must be completely dry first, which can take a day or more depending on the weather, so ask how the installer will make sure of this.

Will a wet-look sealer make my drive slippery?+

Some wet-look products can be more slippery, and applying too much sealer can leave a slippery film, especially on slopes. Ask about coverage rates and whether an anti-slip additive is worth using.

Want to protect your driveway?

Fill in the form or call 01273 115520, and up to 3 local installers will be in touch. It is free and there is no obligation.