A professional clean is often the simplest way to smarten up a tired driveway before thinking about replacing it. This guide sets out published driveway cleaning cost figures, what sealing and resanding add, and what to avoid on resin and tarmac surfaces.
Most cleaning firms price by the size of the drive, so the first thing to know is roughly how many square metres you have. MyJobQuote's guides treat 30 square metres as a single car drive, 60 square metres as a two car drive and 90 square metres as a larger drive. The two national guides below use slightly different size bands, so compare like with like. Neither gives figures specific to Sussex, and local quotes will vary with access, condition and the type of surface.
| Job | Price | Source |
|---|---|---|
| Cleaning only, 30m² | £100 to £160 | MyJobQuote |
| Cleaning only, 60m² | £150 to £250 | MyJobQuote |
| Cleaning only, 90m² | £225 to £350 | MyJobQuote |
| Pressure washing, under 30m² | £100 | MyBuilder |
| Pressure washing, 30 to 50m² | £150 to £250 | MyBuilder |
| Pressure washing, 50 to 70m² | £250 to £400 | MyBuilder |
MyJobQuote says labour, equipment and cleaning products are usually included in its prices. It also breaks cleaning down by surface, giving £120 to £250 for block paving, £100 to £220 for tarmac and £120 to £250 for resin. If you want a quick feel for the size of your drive before you ask for prices, our driveway cost calculator explains how to measure it.
Some firms quote per square metre or by the hour instead of a set price for the job. MyBuilder gives £2 to £5 per square metre for a drive in standard condition and £4 to £8 per square metre where it is heavily soiled, and an hourly rate of £20 to £50. Per square metre pricing tends to suit larger or oddly shaped drives, while a fixed price is easier to compare between quotes. Whichever way a firm prices, ask what is included so that you are comparing the same job.
Condition makes a real difference to the final figure. MyJobQuote says heavy staining adds £50 to £100 and that pre-treatment costs £2 to £5 per square metre. Oil spots, rust marks, tyre marks and deep moss usually need a chemical treatment before or after the wash, and some stains will only fade rather than disappear. A good cleaner will tell you at the outset which marks are likely to remain.
Block paving is the surface most often sealed after cleaning, because a sealer helps lock the jointing sand in place and can make weeds and staining slower to return. Cleaning and sealing are usually booked together, since the paving has to be clean and dry before any sealer goes on. Prices vary between the two guides we use, partly because one quotes whole jobs and the other quotes per square metre. The table shows each figure as its source publishes it.
| Job | Price | Source |
|---|---|---|
| Cleaning and sealing, 30m² | £200 to £300 | MyJobQuote |
| Cleaning and sealing, 60m² | £300 to £450 | MyJobQuote |
| Cleaning and sealing, 90m² | £450 to £650 | MyJobQuote |
| Sealing, 30m² | £200 to £250 | MyJobQuote |
| Sealing, 60m² | £300 to £400 | MyJobQuote |
| Sealing, 90m² | £450 to £600 | MyJobQuote |
| Sealing block paving, per m² | £7 to £15 | MyJobQuote |
| Sealing tarmac, per m² | £5 to £10 | MyJobQuote |
| Sealing concrete, per m² | £6 to £12 | MyJobQuote |
| Block paving, seal only, per m² | £4 to £8 | MyBuilder |
| Block paving, re-sand and seal, per m² | £6 to £10 | MyBuilder |
| Tarmac sealing, per m² | £3 to £6 | MyBuilder |
| Resin bound sealing, per m² | £5 to £9 | MyBuilder |
| Imprinted concrete sealing, per m² | £2 to £3.50 | MyBuilder |
For imprinted concrete, MyJobQuote gives resealing at £4 to £8 per square metre and Less.co.uk at £8 to £15 per square metre, so it is worth getting more than one price. Sealers come in different finishes, from almost invisible to a noticeable wet look, and the choice affects both the appearance and how slippery the surface feels in the rain. Ask any firm which product they use and whether it suits your surface. You can read more on our driveway sealing page.
Block paving relies on the sand in its joints to hold the blocks tight and stop them shifting under the weight of a car. A thorough pressure wash will wash out some of that sand, along with the moss and weeds that have rooted in it. If the joints are left empty, the blocks can loosen and weeds return quickly, so a proper job finishes by brushing fresh kiln-dried sand back into every joint. Kiln-dried sand is used because it is fine and completely dry, so it flows down into narrow gaps.
MyJobQuote prices re-sanding at £2 to £3 per square metre as an extra to sealing, and MyBuilder gives £6 to £10 per square metre for a re-sand and seal together. The paving needs to be dry before the sand goes in, otherwise it clumps on the surface instead of filling the joints. If the drive is being sealed as well, the sealer goes on after resanding and helps bind the top of the joint. Ask whether resanding is included in a cleaning quote, because some firms treat it as a separate line.
There is no fixed timetable, because the right interval depends on how your drive is used and where it sits. A drive under trees or in shade will grow moss and algae far faster than an open, sunny one, and a drive that takes daily traffic will mark more quickly than one used for a single car at weekends. Coastal homes can see more salt and grime, while drives next to lawns tend to collect more soil and weed seed. Many homeowners simply book a clean when the surface starts to look green or stained.
Sealing is a longer cycle than cleaning. Rather than relying on a general rule, ask the firm which sealer they plan to use and how long its manufacturer expects it to last on your surface. In between professional visits, regular sweeping, prompt removal of leaves and quick attention to oil spills make the biggest difference. Keeping drainage channels and gullies clear also stops water sitting on the surface.
Resin and tarmac both need more care than block paving when it comes to cleaning. On a resin driveway, a narrow, high pressure jet held close to the surface can loosen stones, especially at edges and around joints, so a wider fan and a sensible distance are safer. Strong solvents and harsh chemicals can attack the resin binder, so stick to cleaners the installer or resin manufacturer recommends. If your drive is still under an installer's guarantee, check its care instructions first, because the wrong method could affect it.
Tarmac is held together by a bitumen binder, which is softened by petrol, diesel and many solvent-based degreasers. That means fuel spills should be dealt with quickly and solvent cleaners avoided, even on stubborn marks. Very high pressure can also strip the fine material from the surface of older tarmac and leave it looking rough. A cleaner who knows the surface will adjust the pressure and products to suit, so ask how they plan to clean before you book.
You can fill in our short form or call 01273 115520 to get up to 3 free quotes from local driveway installers, with no obligation. We connect you with local firms rather than doing the work ourselves. Tell them the rough size of your drive, the surface, any stains you are worried about and whether you want sealing or resanding included. See our driveway cleaning and pressure washing pages for more on what the work involves.
MyJobQuote gives £150 to £250 to clean a 60m² drive, and MyBuilder gives £150 to £250 for a 30 to 50m² drive or £2 to £5 per square metre. Heavy staining and pre-treatment can add to the price.
MyJobQuote gives £300 to £450 for cleaning and sealing a 60m² drive. MyBuilder gives £6 to £10 per square metre for a re-sand and seal on block paving.
Yes, in most cases. Pressure washing removes some of the jointing sand, and refilling the joints with kiln-dried sand helps keep the blocks tight and slows weed growth.
Yes, but carefully. Use a wide fan at a sensible distance, avoid harsh solvents and follow the installer's or manufacturer's care guidance, because a close, narrow jet can loosen stones.
Sealing can refresh the colour of older tarmac and give some protection against spills. MyJobQuote gives £5 to £10 per square metre and MyBuilder £3 to £6, so get more than one quote.
Prices are published UK averages and include labour. Every job is different, so the quotes you receive will reflect your own property, access and materials.
Tell us about the job and up to 3 local driveway installers will be in touch with quotes. There is no charge and no obligation. Or call 01273 115520.
We use essential cookies to make this site work. With your permission, we would also like to use Google Analytics cookies to understand how people use the site so we can improve it. We do not use advertising cookies. You can change your mind at any time using the cookie settings button. Read our cookie policy for more information.