Block paving cost

Block paving cost per m² varies with the type of block, the pattern it is laid in and the groundwork needed underneath. This guide sets out published UK prices for each, credited to their sources, so you can see where your quotes sit and what should be included in them.

Block paving cost per m² by block type

Concrete blocks are the most common and least expensive choice, while tumbled blocks, clay pavers and natural stone setts cost more to buy and often take longer to lay. Less.co.uk, updated in April 2026, gives an overall installed range of £70 to £120 per m², and its prices by type are shown in the table. Its installed figures cover excavation, sub-base, sand bedding, laying and jointing, but exclude drainage and dropped kerbs.

MyBuilder gives £70 to £120 per m² for materials and labour, and says most projects fall between £85 and £110 per m². The laying pattern makes a difference as well as the block. Herringbone involves more cutting than a simple stretcher bond, which is why Less.co.uk lists it as a premium option.

Installed block paving prices per m²
Block typePrice per m²Source
Standard concrete£70 to £85Less.co.uk (April 2026)
Tumbled£80 to £100Less.co.uk (April 2026)
Permeable£80 to £110Less.co.uk (April 2026)
Herringbone (premium)£85 to £120Less.co.uk (April 2026)
Natural stone setts£100 to £150Less.co.uk (April 2026)
Materials and labour, overall£70 to £120MyBuilder

Block paving driveway cost by size

For a whole drive, MyJobQuote, updated in October 2026, prices concrete, brick and composite blocks separately for three common sizes, with materials and labour included. It gives an overall range of £2,500 to £11,000 and an average of £5,750. It also says a 60m² brick drive costs £5,000 to £6,500 including materials, labour and standard groundwork.

Less.co.uk gives whole-driveway averages and ranges, using 40m² as a typical single-car drive and 80m² as a double. MyJobQuote's regional figures put a 60m² drive in London and the South East at £5,500 to £7,500, which is above its national figures for concrete and brick at that size. The two tables below are kept separate because the sources use different sizes and assumptions.

Block paving driveway cost by size and block, from MyJobQuote (October 2026)
SizeConcreteBrickCompositeSource
30m²£2,500 to £3,500£3,000 to £4,000£3,500 to £4,500MyJobQuote
60m²£4,500 to £6,000£5,000 to £6,500£5,500 to £7,500MyJobQuote
90m²£6,500 to £8,500£7,500 to £9,500£8,500 to £11,000MyJobQuote

Less.co.uk gives £2,850 on average for 30m² (range £2,100 to £3,600), £3,800 for 40m² (£2,800 to £4,800), £5,700 for 60m² (£4,200 to £7,200) and £7,600 for 80m² (£5,600 to £9,600). For a quick figure based on your own measurements, try the driveway cost calculator. Measure the area you want paved, not the whole front garden, and include any paths you plan to add.

Materials, labour and groundworks

Block paving is only as good as what lies beneath it. A typical installation involves digging out to the right depth, laying and compacting a sub-base of crushed stone, screeding a bed of sharp sand, laying and cutting the blocks, then vibrating them into place and brushing kiln-dried sand into the joints. Skimping on the dig or the compaction is the most common reason a drive later dips or ruts where cars park.

MyBuilder breaks the cost down into materials and labour. It gives materials only at £19 to £48 per m² for concrete blocks, £32 to £65 for brick or clay, £60 to £100 for natural stone, £90 to £125 for composite and £60 to £90 for permeable blocks. It puts labour at £30 to £60 per m² and excavation at £8 to £12 per m².

Removing what is already there adds to the bill. MyJobQuote gives old driveway removal at £20 to £50 per m² and excavation at £8 to £12 per m². Waste is heavy and bulky, so ask whether skip or grab lorry costs are in the quote or charged on top.

If the new drive needs vehicle access across the pavement, a dropped kerb is a separate job that most guides leave out of their driveway prices. Less.co.uk lists a dropped kerb at £800 to £2,000, and MyJobQuote puts it at about £2,000. The council has to approve the crossing before any work on the pavement starts, and the contractor must meet the council's requirements. Our dropped kerb cost guide explains the process and the fees in more detail.

Edging, drainage and planning

Every block paved drive needs a firm edge restraint, usually kerbs or edging blocks set in concrete, to stop the blocks spreading and the joints opening. Less.co.uk lists edging at £15 to £30 per metre, but also describes it as included in some of its installed prices, so ask each installer whether edging is priced in. A drive with long, curved or decorative borders will need more edging than a simple rectangle.

Standard block paving with sand-filled joints is generally treated as a hard surface for drainage, so water needs somewhere to go. Permeable block paving uses wider joints filled with fine grit and an open, free-draining sub-base, so rain passes down into the ground. Less.co.uk prices permeable blocks at £80 to £110 per m² installed.

For front gardens in England, GOV.UK guidance says planning permission will be needed for a traditional impermeable driveway covering more than 5 square metres that does not direct water to a permeable area, and it names permeable concrete block paving as a permeable option. The Planning Portal says a new or replacement driveway of any size does not need permission if it is permeable or drains to a lawn or border. Rules differ for flats, conservation areas, listed buildings and Article 4 areas, so check with your local council and see our driveway planning permission advice.

Sealing, cleaning and maintenance

Block paving needs a little regular care to keep it looking its best. Weeds and moss can take hold in the joints, and oil or tyre marks show up clearly on lighter blocks. Many owners have the drive cleaned, re-sanded and sealed every few years, which helps lock the joint sand in place and makes stains easier to wipe away.

MyJobQuote, updated in October 2026, gives block paving sealing at £7 to £15 per m², and £300 to £400 for a 60m² drive, with re-sanding at £2 to £3 per m². MyBuilder gives £4 to £8 per m² to seal block paving only, or £6 to £10 per m² to re-sand and seal. For cleaning, MyJobQuote gives £120 to £250 for block paving.

One real advantage of block paving is that it can be repaired without starting again. If an area sinks or a utility company needs to dig, the blocks can be lifted and relaid, and MyJobQuote gives lift and relay at £20 to £45 per m². Keeping a few spare blocks from the original batch makes a repair much easier to match.

Getting block paving quotes

A fair comparison needs each quote to describe the same job. Ask installers to name the block and pattern, state the depth of dig and sub-base, explain how water will drain and confirm whether edging and waste removal are included. It is also worth asking how they will treat manhole covers and where the drive meets the pavement.

Sussex Driveway is not a paving firm. We connect homeowners with local driveway installers, and if you fill in our short form or call 01273 115520 you can get up to 3 free quotes, with no obligation. You can find out more about block paving before you choose.

Frequently asked questions

What is the average block paving cost per m²?+

Less.co.uk gives an installed range of £70 to £120 per m², and MyBuilder gives the same range with most projects at £85 to £110 per m². The block type, pattern and groundwork all affect where your drive falls.

How much does a block paving driveway cost for two cars?+

MyJobQuote uses 60m² for a two-car drive and gives £4,500 to £6,000 for concrete blocks and £5,000 to £6,500 for brick. Less.co.uk gives £4,200 to £7,200 for 60m², with an average of £5,700.

Is permeable block paving more expensive?+

Less.co.uk prices permeable block paving at £80 to £110 per m² installed, compared with £70 to £85 for standard concrete blocks. The extra cost covers the blocks and the free-draining base, and it can avoid the need for separate drainage on a front drive.

How often should block paving be sealed?+

There is no fixed rule, and it depends on the blocks, the traffic and how exposed the drive is. Many owners reseal every few years after a clean and re-sand. MyJobQuote gives £300 to £400 to seal a 60m² drive.

Can a sunken patch of block paving be fixed?+

Yes, the blocks can be lifted, the bedding and sub-base corrected, and the same blocks relaid. MyJobQuote gives lift and relay at £20 to £45 per m².

Sources for the prices on this page

Prices are published UK averages and include labour. Every job is different, so the quotes you receive will reflect your own property, access and materials.

Compare up to 3 free quotes

Tell us about the job and up to 3 local driveway installers will be in touch with quotes. There is no charge and no obligation. Or call 01273 115520.

We pass your details to up to 3 local driveway installers so they can contact you with quotes. See our privacy policy.